Individual unit
SnowCatcher Stainless — single guard
Buy exactly the count your layout calls for — 304 stainless, screw-down with gasket.
From $7.99 CAD2 optionsChoose options
Stainless steel · Aluminum · Powder-coated
Metal Snow Guards Built To Outlast Canadian Winters
Metal snow guards are screw-down or clamp-on pads in 304 stainless steel or aluminum that hold the snowfield on a metal roof for decades — no UV fade, no cracking at −40 °C. Available individually, in 25-packs with screws and gasket tape, in powder-coated colours, and in the Canadian Maple Leaf edition. Stocked in Paris, Ontario; priced in CAD.
304 stainlessNo rust, no UV fade
8 coloursPowder-coated to match
From $7.99CAD, per guard
SnowCatcher stainless — screw-down roofs
304 stainless steel · screws & gasket tape included · what's screw-down?
25 pack · Complete kit
SnowCatchers Stainless — 25 pack
Screws and gasket tape included — enough for two to three rows on a typical residential face.
$239.99 CAD
SnoCleat™ aluminum — standing seam & PBR
Low-profile cleats, profile-specific
Standing seam · Clamp-on
SnoCleat™ RC — standing seam
Aluminum cleat that grips the seam — no panel penetration, no adhesive cure time.
From $29.99 CAD2 optionsChoose options
PBR panel · Screw-down
SnoCleat™ PBR — screw-down
Shaped to the PBR panel rib — screw-down aluminum hold for exposed-fastener roofs.
From $24.99 CAD2 optionsChoose options
Colour-matched & Maple Leaf editions
Powder-coated finishes · see the colour chart
Maple Leaf · 10 pack
SnowCatchers Maple Leaf — 10 pack
Snow retention shaped like the leaf itself — stainless steel, screw-down, unmistakably Canadian.
$145 CAD
Contractor · 100 pack · 8 colours
Powder-Coated SnowCatcher™ — 100 pack
Bulk colour-matched guards for full roofs and crews — pick your colour from eight powder-coat finishes.
From $999.95 CAD8 coloursChoose colour
Spec it right
Stainless, Aluminum Or Powder-Coated?
| SnowCatcher stainless | SnoCleat™ aluminum | Powder-coated colours | |
|---|---|---|---|
| Material | 304 stainless steel | Aluminum | Steel, powder-coated (8 colours) |
| Roof type | Screw-down / exposed fastener | Standing seam (RC) or PBR (PBR) | Screw-down / exposed fastener |
| Attachment | Screws + gasket tape | Clamp-on (RC) or screw-down (PBR) | Screws + gasket |
| Look on the roof | Bright stainless, low profile | Slim cleat, minimal shadow line | Disappears into the roof colour |
| Formats | Single from $7.99 · 25-pack $239.99 | PBR from $24.99 · RC from $29.99 | 100-pack from $999.95 |
| All prices | Canadian dollars (CAD), shipped from Paris, Ontario — no duties | ||
Quick answers
Metal Snow Guard Questions, Answered
Metal or polycarbonate snow guards — which should I choose?
Metal guards suit screw-down roofs, harsh exposure and buyers who want a multi-decade service life with zero UV concern. Polycarbonate guards suit standing seam (adhesive, no penetration) and anyone who wants the guard to disappear on the panel. Many roofs use both.
Will stainless steel snow guards rust on my roof?
SnowCatchers are 304 stainless steel — the same grade used in marine hardware. They won't rust, streak the panel or fade, even through salt-air winters in Atlantic Canada.
Can I get metal snow guards to match my roof colour?
Yes — the powder-coated SnowCatcher 100-pack comes in eight colours matched to common Canadian panel finishes. Check yours against the colour chart before ordering.
Do metal snow guards work on standing seam roofs?
Yes — the SnoCleat™ RC clamps to the seam with no panel penetration. For heavier loads on standing seam, step up to a SnoBar® rail system.
How many metal snow guards does my roof need?
It depends on your roof's dimensions, pitch and local ground snow load — there's no safe universal number. We calculate it free and back it with a warrantied quote, usually within one business day. Individual units mean you can buy exactly that count.
Warrantied quote · Canadian stock · CAD pricing
Tell us your roof. We'll count the guards.
Dimensions, pitch, panel type and your town — we'll return a warrantied layout with the exact guard count and spacing for your local snow load, usually within one business day.
-
SnowCatcher Stainless Steel Snow Guard – Screw-Down Metal Roof Snow Retention | 304 SS | Canada Snow Guards 
SaleSnowCatcher Stainless Steel Snow Guard – Screw-Down Metal Roof Snow Retention | 304 SS | Canada Snow GuardsSnowCatcher Stainless Steel Snow Guard – Screw-Down Metal Roof Snow Retention | 304 SS | Canada Snow Guards
Sale price $7.99 CAD Regular price $9.99 CAD -
SnoCleat™ PBR Screw-Down Aluminum Snow Guard (Canada) 
SnoCleat™ PBR Screw-Down Aluminum Snow Guard (Canada)SnoCleat™ PBR Screw-Down Aluminum Snow Guard (Canada)
$24.99 CAD -
SnoCleat™ RC Standing Seam Snow Guard (Canada) 
SnoCleat™ RC Standing Seam Snow Guard (Canada)SnoCleat™ RC Standing Seam Snow Guard (Canada)
$29.99 CAD -
SnowCatchers Stainless Steel Maple Leaf Snow Guards – 10 Pack 
SnowCatchers Stainless Steel Maple Leaf Snow Guards – 10 PackSnowCatchers Stainless Steel Maple Leaf Snow Guards – 10 Pack
$145.00 CAD -
SnowCatchers Stainless Steel Snow Guards – 25 Pack with Screws & Gasket Tape 
SaleSnowCatchers Stainless Steel Snow Guards – 25 Pack with Screws & Gasket TapeSnowCatchers Stainless Steel Snow Guards – 25 Pack with Screws & Gasket Tape
Sale price $239.99 CAD Regular price $279.95 CAD -
Powder-Coated Metal SnowCatcher™ Snow Guards – Colors (100 Pack) 
Powder-Coated Metal SnowCatcher™ Snow Guards – Colors (100 Pack)Powder-Coated Metal SnowCatcher™ Snow Guards – Colors (100 Pack)
$999.95 CAD
Canada Metal Snow Guard Estimator
Pitch
Calculator uses your spacing rule as the target distance between rows and then divides the run evenly:
Rows = ceil(Run ÷ Spacing)
Dimensions
Guards per row uses:
Guards/Row = ceil((Eave × 12) ÷ Valley)
Metal Snow Guard Results ($9.998 CAD/unit)
| Rows | Guards/Row | Total Units | Total Cost (CAD) |
|---|---|---|---|
| — | — | — | — |
Divide the roof into equal sections by spacing multiple rows evenly up the slope.
Why Buy a Screw-Down Metal Snow Guard Kit for Your Canadian Metal Roof?
Everything you need in one order — pre-counted screw-down guards, stainless hardware, EPDM gaskets, and a layout guide sized to your roof and snow load zone. No missing pieces, no second trips to the supplier.
📦
Complete Kit — One Order
Screw-down snow guards, stainless steel fasteners, EPDM gaskets, and a step-by-step installation guide — all matched and shipped together. Nothing to source separately on install day.
❄️
Rated to -40°C
All-metal construction holds full structural integrity in extreme sub-zero temperatures across Northern Ontario, Quebec, Alberta, and the Prairies — no cracking, no creep, no failure.
🏗️
Pre-Calculated for Your Snow Load
Kits are sized to your roof pitch, rafter length, panel type, and regional PSF load — so you get exactly the right number of guards for full-roof coverage without over-ordering.
⚠️
Reduces Liability & Risk
Helps meet NBCC safety expectations above walkways, loading docks, and high-traffic areas — one correctly installed kit is the most cost-effective way to manage that exposure.
Screw-Down Metal Snow Guard Kits for R-Panel, PBR & Corrugated Roofs
Our screw-down kits are built for exposed-fastener and ribbed metal roof profiles — the most common metal roof type on Canadian residential, agricultural, and light commercial buildings.
Most Popular Kit
Individual Screw-Down Snow Guard Kit
The individual guard kit includes metal screw-down snow stops pre-counted for your panel layout, plus stainless steel fasteners and high-grade EPDM gaskets — everything needed for a watertight mechanical installation. Designed for R-Panel, PBR, corrugated, and ribbed metal profiles. Guards fasten directly through the panel flat into the purlin or decking below, creating maximum shear resistance. Each kit ships with a placement guide calculated for your slope and PSF load zone so every guard lands in the correct position.
- Includes: Guards + stainless fasteners + EPDM gaskets + layout guide
- Profiles: R-Panel, PBR, corrugated, ribbed
- Fastens into: Purlins or roof decking
- Best for: Residential, agricultural, light commercial
Screw-Down
EPDM Sealed
Kit Includes All
High Snow Load Screw-Down Kit — Heavy PSF Zones
For roofs in Northern Ontario, Quebec, the Maritimes, Alberta foothills, and BC mountain corridors where ground snow loads exceed 50 PSF, a high-density screw-down kit provides tighter guard spacing and higher shear capacity per row. Includes additional guards calculated for the elevated load, all stainless hardware, and EPDM gaskets rated for aggressive freeze-thaw cycling. Identical installation method to the standard kit — just more guards, closer together, exactly where they need to be.
- Includes: Guards + stainless fasteners + EPDM gaskets + high-load layout guide
- Designed for: PSF loads above 50
- Spacing: Tighter rows calculated for your load zone
- Best for: Northern regions, mountain corridors, heavy-snowfall zones
High Load
Tight Spacing
Full Hardware
Custom Full-Roof Screw-Down Kit — Sized to Your Project
Not sure which standard kit covers your roof? We build custom screw-down snow guard kits based on your exact panel type, roof dimensions, pitch, and regional snow load (PSF). Tell us your details and we'll calculate the correct guard count, row spacing, fastener spec, and EPDM gasket quantity — packaged as a single ready-to-install kit. Used by roofing contractors and homeowners across every province. All Canadian inventory: ships same or next business day, no cross-border fees.
- Sizing: Roof area, pitch, PSF load, and panel type
- Ships from: Canadian warehouse — no duties or brokerage
- Turnaround: Same or next business day for in-stock kits
Custom Sized
In Stock
Ships Fast
Screw-Down Metal Snow Guard Kits FAQ — Canada
Can't find your answer? Ask us →What does a screw-down metal snow guard kit include?
Each kit includes metal screw-down snow guards pre-counted for your roof size, stainless steel fasteners, high-grade EPDM-sealed gaskets, and a step-by-step installation and layout guide. Everything is matched and shipped together — no separate hardware runs required. You'll have every component needed to complete the installation in one delivery.
What metal roof profiles do screw-down snow guard kits work on?
Screw-down snow guard kits are designed for exposed-fastener and ribbed metal roof profiles — including R-Panel, PBR, corrugated, and ribbed metal panels. These are the most common metal roof types on Canadian residential homes, barns, farm buildings, shops, and light commercial structures. If your roof has visible screws or ribs running down the slope, a screw-down kit is the right solution.
How do I know which kit size I need for my screw-down metal roof?
Kit sizing depends on your panel type, roof pitch, rafter length, and your region's ground snow load (PSF). Higher-load zones — Northern Ontario, the Maritimes, Alberta foothills, and BC mountain corridors — require more guards per row and tighter row spacing than southern residential roofs. Request a free layout quote and we'll calculate the exact guard count, row placement, and fastener spec for your specific roof.
Will screw-down snow guards leak or damage my metal roof?
No — when properly installed with the included EPDM-sealed gaskets. Each fastener point is sealed with a high-grade EPDM gasket specifically rated for metal roofing and Canadian freeze-thaw cycling. EPDM maintains its seal flexibility down to -40°C, so the fastener points stay watertight through the most aggressive winter-to-spring thaw cycles. Correct fastener placement into purlins or decking (as outlined in the included layout guide) is critical for both seal integrity and shear performance.
Can I install a screw-down snow guard kit myself?
Yes — screw-down kits are designed for contractor and DIY installation. You'll need a drill and a basic socket set. Each kit ships with a full layout guide covering guard placement, row spacing, fastener torque, and EPDM gasket seating. Following the guide precisely — especially fastening into purlins rather than the panel flat alone — ensures maximum holding strength and a watertight seal.
Do the kits ship from within Canada?
Yes — all screw-down metal snow guard kits are stocked in Canada and ship nationwide with no U.S. customs, duty, or brokerage fees. Orders typically ship same or next business day for in-stock kits. We deliver to every province and territory, from Vancouver Island to Newfoundland and Labrador.
Do I need a snow guard kit if I already have gutters on my metal roof?
Yes — gutters are one of the first things metal roof snow slides destroy. A full sheet of snow and ice releasing off an unprotected corrugated or R-Panel roof can rip gutters and downspouts clean off the fascia. A properly installed screw-down snow guard kit holds snow in place so it melts gradually — protecting gutters, downspouts, and everything below the roofline.
Screw-Down Snow Guard Kits for Residential, Agricultural & Commercial Metal Roofs
Roof avalanches on corrugated and R-Panel metal roofs aren't just a nuisance — they're a liability. A properly installed screw-down snow guard kit is the most direct way to protect people and property below.
-
01Residential Homes & Cottages Screw-down kits protect gutters, entryways, decks, and vehicles below steep R-Panel and corrugated roofs — especially critical on homes in heavy-snowfall zones across Ontario, Quebec, and BC
-
02Agricultural Buildings & Barns Cost-effective screw-down kits for corrugated and R-Panel barn roofs — protect livestock, equipment, and personnel from roof snow slides on farm buildings across Ontario, Saskatchewan, and Alberta
-
03Light Commercial & Retail Buildings Screw-down kits on PBR and R-Panel commercial roofs protect customer walkways, loading docks, and parking areas — reducing liability above high-traffic zones at service centres and storefronts
Ready to price a project? Request a free screw-down kit layout & quote.
Screw-Down Metal Snow Guard Kits.
Canadian-Stocked. Engineered for Our Winters.
Request a free kit layout and quote — we'll size the right screw-down snow guard kit to your R-Panel, PBR, or corrugated metal roof and regional snow load.